Replying because I am encountering the same issue. Not using batch script. Just using the GUI with already preprocessed data. When in the Denoising & Quality Control tab, the same error described here appears.

Hopefully someone who has solved this issue has suggestions to share.

Thanks

Originally posted by Fabian Wissing:

Dear CONN community,

I am importing already preprocessed functional data, masks, and covariates into CONN toolbox using the following batch script:

clear batch;
batch.filename=fullfile(conn_dir,'conn_batch_new.mat');

batch.Setup.isnew=1;
batch.Setup.done=1;
batch.Setup.overwrite=1;

batch.Setup.nsubjects=1;
batch.Setup.RT=2;

conditions = {'rest','cond1', 'cond2', 'cond3', 'cond4'};
nconditions = numel(conditions);
batch.Setup.covariates.names = {'realignment'};

batch.Setup.functionals{nsub} = {fullfile(data, 'swarfunc.nii')};
batch.Setup.structurals{nsub} = {fullfile(data, 'swmanat.nii')};
batch.Setup.masks.Grey{nsub} = {fullfile(data, 'gm_mask.nii')};
batch.Setup.masks.White{nsub} = {fullfile(data, 'wm_mask.nii')};
batch.Setup.masks.CSF{nsub} = {fullfile(data, 'csf_mask.nii')};
batch.Setup.covariates.files{1}{nsub} = {fullfile(data, 'rp_func.txt')}; conds = load(fullfile(data, 'conditions.mat'));
for ncond=1:numel(conditions)
    if ncond==1
        batch.Setup.conditions.names{ncond} = 'rest';
        batch.Setup.conditions.onsets{ncond}{nsub}{1}=0;
        batch.Setup.conditions.durations{ncond}{nsub}{1}=inf;
    else
        batch.Setup.conditions.names{ncond} = conds.names{ncond-1};
        batch.Setup.conditions.onsets{ncond}{nsub}{1}=conds.onsets{ncond-1};
        batch.Setup.conditions.durations{ncond}{nsub}{1}=conds.durations{ncond-1};
    end
end

batch.Denoising.done=1;
batch.Denoising.overwrite=1;

batch.QA.foldername = [fullfile(project_dir, 'results','qa','CONN_2026')];
batch.QA.plots = {'QA_DENOISE histogram';
'QA_DENOISE timeseries';
'QA_DENOISE FC-QC';
'QA_DENOISE scatterplot'};

conn_batch(batch);

The script runs without errors. However, when opening the project using the GUI and selecting the Denoising & Quality Control tab, I get the following error:

Unable to compute Data Sensitivity. Expected the following QC_ 2nd-level
covariates: 
QC_ProportionValidScans|QC_MeanMotion|QC_MeanGSchange|QC_NORM_struct|QC_DOF|QC_PeakFC|QC_StdFC

ERROR DESCRIPTION:

Index exceeds the number of array elements. Index must not exceed 0.

Error in conn (line 7570)
  if
conn_existfile(fullfile(CONN_x.Preproc.qa.folders{3},'DataSensitivityScore.mat'))

Error in conn_menumanager (line 125)
  
feval(CONN_MM.MENU{n0}.callback{n1}{1},CONN_MM.MENU{n0}.callback{n1}{2:end});
CONN25.b
SPM12 + DAiSS DEM FieldMap MEEGtools
Matlab v.2023b
project: CONN25.b
storage: 5923.6Gb available

In the Denoising & Quality Control tab, no figures appear in Preview Effect of Denoising, and all QC parameters have question marks. The folder results/qa/CONN_2026 only contains:

• 
  

  QA_DENOISE.subject001.mat

  
  


• 
  

  QA_DENOISE_scatterplot.subject001.mat

  
  

and none of the other expected QA files.

Could this indicate that some QA or QC covariates were not generated during the batch processing? Is there an additional step required when importing already-preprocessed data?

Thank you for any suggestions.